George Wiseman’s AquaCure AC50 V2 can switch between 250VAC and 120VAC to generate up to 50 liters per hour (lph) of special mixture of hydrogen and oxygen gases (Brown’s gas).
This is about 833 mL/m of 66% hydrogen and 33% oxygen…
Why would you want the AquaCure over all the ‘other’ hydrogen options in the marketplace? People who do the research and comparison have no problem seeing that the AquaCure surpasses all other options for SAFE and practical use… And is less costly than many alternatives that do not have the same safety or functional features.
Note that we normally ship the next business day after purchaseThe AquaCure is LOADED with SAFETY features (see below).
The AquaCure can be used continuously with minimal maintenance
(just add pure water as needed and rinse it about once every 100 hours)
We focused our attention on achieving optimum safety, effectiveness, user-friendliness and durability while keeping the cost as low as possible. We DELIBERATELY built the AquaCure from an electrolyzer meant to provide Brown’s Gas to fuel a micro-torch, we seriously upgraded that simple machine to have safety and functionality better than any other Brown’s Gas machine in the world; even ones costing over $30,000.
The AquaCure ‘looks commercial’ because it is built to worldwide industrial and safety standards.
Also, this ‘sales page’ was written by the inventor (George Wiseman), so it isn’t polished like ‘competitors’ websites… but you’ll get the raw, honest truth.
George Wiseman is an inventor that has 30+ years experience building the world’s most practical, safe and optimized Brown’s Gas electrolyzers.
For LEGAL REASONS we need to state up front that the AquaCure is NOT defined as a MEDICAL DEVICE by the FDA and therefore we MUST REFER YOU TO OUR MEDICAL DISCLAIMER.
‘Legal’ uses would be for fueling a micro-torch and providing water and gas for the health of plants, fish, birds, reptiles, and other mammals.
Brown’s Gas (they call it OxyHydrogen) is medically certified in China, Japan, etc. and is EXTENSIVELY used for human health all through Asia.
Hundreds of scientific studies have proven that it is safe for plants and animals to use for drinking and breathing. Current studies are proving that humans are having all the same benefits proven on Plants and Animals but until we get medical certification we cannot (for legal reasons) recommend it for human use.
Note: A study of all the studies (including on humans) shows NO negative side effects of hydrogen, only positive benefits.
See our full Medical Disclaimer:
The AquaCure draws about 250 watts and comes in BOTH 120 VAC and 240 VAC option (click the correct version button). North America and Japan are 120 VAC, Pretty much everywhere else in the world is 240 VAC
AquaCure comes with access privileges to an online AquaCure Resources (some there but still under construction), which will give you instruction videos, tips, options and (quite frankly) anything we can think of to enhance your user experience. The online Resources are updated as needed to assure that you will always have access to the most recent information.
The Resources is where you’ll find:
AquaCure AC50 Setup and Operation Videos
AquaCure Setup and Operation Manuals, User-Guides and Updates
You can access your online Resources by logging into your user account.
No user-account or login is required to place an order.
The Website automatically creates a user-account for you, as you place your first order.
Warranty includes parts, labor and shipping if issue is manufacturer related. We’ve been in business since 1984 and expect to be in business at least another 20 years. Warrantee is assigned to the Eagle-Research customer (the one who paid us the money) and is not usually transferable.
If Warranty is invalid (because of resale or user abuse), we will still repair any issues for lifetime if the owner pays for parts, labor and shipping. We still support all the products we’ve ever sold.
100% SATISFACTION GUARANTEE:
We often get the question…. Does Brown’s Gas help (fill in the blank)???
We can’t guarantee any particular result because every body is different.
However, because we are SO CERTAIN you’ll be happy with this machine, we have a 100% no questions asked one YEAR money back satisfaction guarantee on your first AquaCure Purchase
(1 year from the date you receive your first machine).
You don’t need to state a reason if you want to return the machine (even after used for 12 months), just ask for an RMA number and instructions to properly send it back and (once we evaluate the machine) we’ll refund your purchase price (shipping, taxes and duty costs/fees are not refunded).
We’ve been in continuous business since 1984 and our business reputation is impeccable.
Our customers satisfaction comes first!
We reserve the right to discount the refund to cover any customer related damage.
(normal wear and tear is expected and will not be discounted).
Note that our Resources, Warranty, Satisfaction Guarantee, and Refund Policies are privileges ONLY for purchases DIRECTLY from Eagle-Research.com (where you paid us the money).
If purchasing from a 3rdparty (like a distributor, other manufacturer, etc.), be sure to confirm what THEIR policies are (or are not).
Just because you acquired an AquaCure (like from eBay) does not mean you are OUR customer. Purchasing from THIS website qualifies you as OUR CUSTOMER and you’ll receive the FULL SATISFACTION GUARANTEE.
AquaCure is designed to operate continuously without over-heating. Some electrolyzers ‘out there’ can only operate for a short time (often less than an hour) without having to be shut off to cool down. The AquaCure is designed to operate 24/7/365 and doesn’t even need to be shut off when refilling with water. This is very handy in applications that need continuous operation.
The AquaCure keeps it’s operating temperature below 39°C to reduce lye loss (from moisture in the gas) and to increase electrolyzer lifespan.
LOW LIQUID LEVEL SHUTOFF
AquaCure has a low water level switch to automatically shut off the machine if the liquid level gets low.
Running ANY electrolyzer out of water can cause electrode degradation, internal over-heating and explosions that could lead to damage and harm.
Most electrolyzer manufacturers don’t mention this issue because they do NOT have low liquid level shutoff.
They depend on you to visually check the liquid level frequently to prevent damage to the machine.
AquaCure shuts off the gas production when liquid level gets low, so no danger condition can exist. AquaCure also has a low level alarm and indicator light, so there is no question when the liquid is low.
Liquid level control is REQUIRED in applications where the electrolyzer is going to operate unattended for long periods of time; for examples:
- When needing to be run all night.
- Using Brown’s Gas to continuously bubble water for hydroponics / aquaponics.
- Automatically feeding Brown’s Gas to a furnace for combustion enhancement.
- Creating ‘NEW WATER’. New Water is water that’s had its memory entirely erased and the things that you can do with it (like programming for health and transmutation) are astounding!
We’ve also added a VERY CONVENIENT yellow ‘refill’ indicator light. that tells you when to refill (without alarms and shutoff). This helps keep the liquid level in the recommended 3/4 full to full range.
HIGH LIQUID LEVEL SHUTOFF
George Wiseman’s AquaCure AC50 V2 has a high water level switch to automatically shut off the machine if the liquid level gets high.
If electrolyzers get over-filled they can spit lye out into your gas . Also the high level sensor allows for future upgrade to automatic water fill.
Over-filling can be caused by a failed anti-backfill system (check valves fail), so the high liquid level shutoff is also an important backup safety feature.
ADJUSTABLE GAS PRODUCTION
The AquaCure AC50 allows people to easily and accurately VARY the gas output. This functionality is VITAL FOR SAFETY when making optimized hydrogen mixtures.
Most ‘other’ electrolyzers ‘out there’ do not have this essential feature.
The AquaCure model EA-H160 could safely vary its gas production, but its system (using a mechanical restriction valve) was clumsy because it was ‘inconvenient’ to accurately measure the gas output.
George Wiseman’s AquaCure AC50 V2 made gas volume adjustment convenient and accurate with electronic buttons and display so that a person can KNOW EXACTLY how much Brown’s Gas is being produced… And this is VITAL, not only for safety but to individually optimize the effectiveness of all the Brown’s Gas protocols.
Brown’s Gas is 100% NON-toxic. There is nothing in the gas that is toxic. It could literally be breathed 100%… Except…
The problem, (that everyone else is scared to tell you for fear you won’t buy their machine) is that hydrogen (when mixed with oxygen) is the world’s most explosive gas…
And you do NOT (I’m assuming) want an explosion to hurt you!
WE WANT YOU TO BE SAFE! So we tell you the hard truths no one else will AND we design the AquaCure to be SAFE.
Mixtures of air that contain more than 4% hydrogen are potentially EXPLOSIVE. So the SAFE SOLUTION is to prevent a mixture that contains more than 4% hydrogen…
…The AquaCure AC50 is specifically DESIGNED to help you prevent a gas mixture that contains more than 4% hydrogen… yet set (optimize) the gas volume for OPTIMUM value.
Hydrogen has been proven beneficial in hundreds of scientific studies, the studies are usually done at 2% hydrogen in air; for safeties sake; and at 2% there is still a full therapeutic health benefit with NO negative side effects.
There is NO practical need to exceed 2% hydrogen in the inhaled breath. Once the blood is saturated, the body exhales almost as much as inhaled (the body just exhales the excess).
MOST other Hydrogen for Health options out there do NOT have gas volume adjustability and usually just limit gas production to less than optimal therapeutic value …
But ‘fixed gas production’ doesn’t address the issue that smaller beings (even infants) could also benefit from hydrogen supplementation and need FAR LESS hydrogen (for safety). They breath less air, so the hydrogen volume needs to be correspondently reduced!
George Wiseman’s AquaCure AC50 V2 can have FULL GAS PRODUCTION (50 lph) for all other applications / protocols AND then the gas production can easily and appropriately be reduced to keep the mixture breathed ‘non-explosive’ for any sized ‘mammal’.
One thing that current medical science is ‘re-discovering’ is that frequencies matter.
So for those who understand what frequencies will help ailments, we’ve added the (electronically controlled) ability to ‘impress’ frequencies onto the Brown’s Gas.
The AquaCure has an advanced ‘anti-backfill’ feature, that reliably prevents the water in the Humidifier and Drinking Water Bubbler from ‘back-feeding’ (getting sucked back) into the electrolyzer upon shutdown.
Many electrolyzers do not have this feature and/or the ‘feature’ isn’t reliable.
Backfilling isn’t ordinarily a ‘big problem’ in itself…
EXCEPT it can cause the AquaCure to be over-filled, resulting in lye ejection.
We’ve added a ‘reserve’ tank to the machine, so it can operate for hours longer between ‘refills’. This is needed when using the AquaCure for applications requiring continuous use. At 100% gas production the AquaCure AC50 can go 10 hours on a fill; at 40% production, the AquaCure AC50 can operate over 24 hours on a fill.
TOWER CAP pre-scrubber
The main purpose of the Tower Cap is to prevent lye from leaving the AquaCure. It is ‘tall enough’ that the lye mist tends to settle out and (mostly) pure gas comes out of the top of the Tower Cap.
The Tower Cap also allows you to see if you have foaming, prevents ‘plugging’ and reduces maintenance. We’ve been using this ‘tower technology’ on our electrolyzers since 2007, based on research we did in 1996.
HUMIDIFIER (lye scrubber)
The function of the Humidifier is to filter out any residue of lye (NaOH) that comes out of the machine with the gas. It normally does a really good job. If there is not enough liquid or if it isn’t changed often enough, this function becomes compromised.
Even though we’ve designed the AquaCure for a 20+ year service life, all equipment needs regular maintenance. So we’ve included an hour-meter to make it easy to know when to do the maintenance rinsing, (about every 100 hours of use).
ADEQUATE GAS VOLUME
AquaCure Gas Volume is sufficient (~ 50 LPH) to ‘charge’ water quickly and supports the 6 protocols (including the potential of DDW water production, making NEW water and fueling the micro-torch).
1. Bubble (infuse the water with Brown’s Gas) for healthful drinking and for feeding to plants and animals. Can also be used to enhance hydroponics, aquaponics, fish growth, etc.
2. Bubble (infuse the water with Brown’s Gas) for topical treatment of skin issues and wounds. Also bubble foot bath or bath water for full body treatment.
3. Bag limbs to use Brown’s Gas gas for external treatment of skin, wounds and various pain relief (like arthritis and carpel tunnel).
4. Direct BREATHING (inhalation) of Brown’s Gas gas (hydrogen / oxygen mixture), to efficiently put the hydrogen directly into the blood for fast, efficient whole body hydration.
5. We are developing the apparatus that will retrofit to ALL AquaCures, that will allow production of Deuterium Depleted Water (DDW). We do not yet have a specific time this option will be released.
6. There are ‘developing application’ protocols that use ‘NEW WATER’ that is generated by collecting the condensation of the Brown’s Gas flame. The AquaCure is designed to ‘make’ New Water (using the correct attachments). More on that subject will be introduced later; just note that the AquaCure is ALREADY DESIGNED for astonishing attachments to come.
AquaCure has a timer switch, for convenience and efficiency. Treatments can be easily timed so no gas is produced beyond timing needed. It shuts itself off when you are finished.
The timer switch also has a ‘continuous’ setting, so that Brown’s Gas can be produced for extended times (until the low liquid level sensor shuts it off).
Note: As of August 2021, both the 120 VAC and the 240 VAC AquaCure AC50 have a custom made electronic timer switch.
MASTER SHUTOFF SWITCH
This switch completely shuts off power to the AquaCure. Most other electrolyzers only shut off the ‘power’ wire (like the timer switch would), leaving the neutral wire connected to the Grid. For safety, we shut off BOTH the power and neutral wires.
AquaCure has long life, reliable electrical and electronic components and electrolyzer chamber. Do NOT assume that because it ‘looks’ like a China VING, that it is a VING. It is significantly upgraded (at a cost several times higher than the VING retail).
AquaCure is built to CE safety standards, which I’ve then UPGRADED to pass CSA/UL and Australian safety standards.
Some manufacturers try to bypass this (expensive) certification by claiming that all components used are safety certified and while this is good (if true and includes the electrolyzer chamber too), it does NOT mean that the MACHINE as a whole is built to safety standards.
There’s no USA law that states any machine needs to be safety certified to be sold, but many business insurance plans require ALL equipment used in a building be safety certified.
If there is a fire, etc. and there is a SINGLE piece of uncertified equipment in the building (even a light switch that did not cause the fire), their insurance becomes invalid, even if they had properly kept up their payments.
Besides, wouldn’t YOU feel more secure using equipment that has been completely and independently inspected, tested and SAFETY certified to rigorous industry agreed standards?
In addition to all the above, we do our OWN multi-step testing on every single AquaCure machine manufactured, so there is NO QUESTION that it will perform perfectly for you.
If someone else makes a better machine than I can, beats my retail price and provides as good or better service; I swear I’ll stop making mine and recommend everyone to the better machine.
And I will NOT (as many others do) compromise SAFETY for lower cost, even if a higher price costs me sales. My customer’s well being is more important than money.
George Wiseman’s AquaCure AC50 V2 has a 2 psi electrical shutoff AND a 3 psi over-pressure gas relief.
These are IMPORTANT safety factors because when water is turned into gas, it expands and ‘wants to’ take up 1800 times more space. If confined to a specific volume, (enclosed container without release) the internal pressure rises until the machine bursts and/or explodes.
Since the Brown’s Gas is used as created, on-demand, (never stored) there should never be a case where the pressure would rise too high…
BUT what if the gas output hose gets trapped (like pinched under a chair leg, (as happened to me) or gets kinked under a pillow as someone sleeps…
Further, over-pressure control (along with an appropriate torch and backfire filter) then allows the Brown’s Gas to be safely used to fuel a torch; a nice additional useful feature to have.
NOTE: The original basic chassis (VING) comes from China with 15-20 psi operating pressure, which is (in my opinion) absolutely DANGEROUS!
In addition, it’s mechanical pressure relief is set at 40 psi. It’s so dangerous I wouldn’t even use it for its original purpose (acrylic polishing).
I’ve tried to tell the Chinese this but they arrogantly believe no one can ‘improve’ on their design…
Because of my DECADES of research and experience with Brown’s Gas, I KNOW Brown’s Gas is MUCH MORE explosive as its pressure rises.
At ambient pressure, a pop bottle can contain a Brown’s Gas explosion. As the pressure rises, the explosion is logarithmically more powerful and at 20 psi, it’s like holding an M80 firecracker. At 40 psi it’ll split apart a metal container.
Thus multiple and redundant over-pressure controls are important SAFETY features!
So I’ve changed the VING pressure switch to MY safety standard of ~ 2 psi, which I can do because, when combined with my other technologies, I solve all the issues that require the Asians use up to 20 psi. I do this for YOUR safety!… And my peace of mind.
AquaCure uses a lightly caustic electrolyte mixture designed to achieve practical efficiency with minimal foaming and to promote long internal plate life.
(about 3 ounces (80 grams) of lye in about a quart (1 liter) of water).
This mixture IS technically caustic but can be safely used if appropriate care is taken. It’s about as caustic as strong dish soap.
Due to (present) manufacturing development and market studies, shipped product may look slightly different from depicted.
26 lbs (shipping weight), 18″Lx16″Wx14″H (shipping box size),
The AquaCure itself is about 12 inches high (excluding the 10 inch Tower Cap), 12 inches long and 9 inches wide and weighs about 16 lbs in operation.
The AquaCure makes gas with State-of-Art efficiency levels. It draws about 240 watts when at full gas production. The 120 VAC version uses about 2 amps and the 240 VAC version uses about 1 amp.
that normally come with the George Wiseman’s AquaCure AC50 V2.
1. Basic Setup and Operation Manual NOT INCLUDED IN BOX (download PDF from user account)
(updates, upgrades, videos and additional information will be in the online AquaCure Resources).
2. Tower Cap (with check valve installed) + regular cap for shipment.
3. 1 of Humidifier (to scrub Brown’s Gas of any possible lye mist) + Humidifier attachment hose and Humidifier Holding Bracket (screws onto side of AquaCure for convenience)
4. Medium (1 liter) Water Bubbler
+ 4 foot Humidifier to Water Bubbler attachment hose
So you can set up to infuse your water AT THE SAME TIME as safely using the gas. I love doing two things at the same time 🙂
5. Additional bubbling stone
So that you can bubble the Brown’s Gas into other containers of water, including baths, etc.
6. 1 of Soft Silicone Brown’s Gas Spot Applicator
So you can spot treat eyes, sore muscles, wounds, rashes, age spots, etc.
7. 1 of 7 foot Accessory hose
(for above Spot Applicator and remote bubbling stone)
8. Tee Kit, so that the gas can be split between two (applicable) applications.
9. 1 of 50 mL syringe; to fill the AquaCure with water.
10. 1 of safety Goggles
11. 1 pair of Nitrile Gloves
12. AquaCure Wash Cloth to catch drips
13. A Total Dissolved Solids (TDS) Meter, to test the Distilled water you are putting into the Humidifier and AquaCure, The water needs to be PURE for optimal gas production and machine longevity..
14. An initial ‘Solution Fill’ funnel to help prevent drips.
OPTIONAL ATTACHMENTS AT BOTTOM OF THIS PAGE:
You can order these in addition to the above attachments that already come with the AquaCure. Many say ‘extra’ because those items already come with the AquaCure but you can buy ‘extras’.
We seriously recommend the WaterLover’s distiller. The AquaCure requires PURE water to operate. Many people buy their distilled water at a local store and that’s OK, but carrying gallons of water gets tiring AND costs more money than making your OWN distilled water.
I (George Wiseman) researched distillers and found one that SHOULD (because of it’s quality) be priced in the $1500 range, but sells for only $419. I have been using 3 of them in my home and workshop for years now.
Brown’s Gas is BIG in Asia largely because of the COST to build the machines in America. For example, this company has made Brown’s Gas machines since 1964 and their machines do NOT have the same safety standards as the AquaCure design. To implement ALL my safety features, I estimate they’d need to retail their machine in the $5000.00 range.
I went to China and imported a ‘basic’ reasonable quality electrolyzer (known as the VING) to use as the AquaCure ‘chassis’. Frankly (and I’m sorry to say) because they can retail at 10% of my American manufacturing cost…
But the ‘QUALITY’ of the galvanized and powder coated finishes is NOT PERFECT. I’m trading cosmetic issues for cost, so I can sell this machine for $2499 instead of $5000.
I then tear it completely apart and upgrade it with all the safety standards on this page (Standards I’ve learned from building and selling thousands of practical, efficient and innovative electrolyzers since 1984)… It takes several hours and hundreds of dollars in parts to upgrade;
and this allows me to sell a NEW SAFER, high quality machine (which I re-name AquaCure) at $2,499. I DO NOT compromise SAFETY or FUNCTION on my machines. No one in the world does a better job, even the ones that sell for more than twice the cost.
This reasonably priced AquaCure is a ‘game-changer’ because now most people can actually afford to use the amazing Brown’s Gas gas safely in their own home.
TESTIMONIALS (See a few of them in the Resources)
We’ve been selling electrolyzers optimized for health since 2007. We have AMAZING testimonials but don’t yet have them on this website. We’re working hard to get a new website fully online and will have the testimonials up ASAP.
LEGAL MEDICAL DISCLAIMER:
THE STATEMENTS ON THIS WEBSITE HAVE NOT BEEN EVALUATED OR APPROVED BY THE AMA, CDC, FDA, WHO, ETC.
~ Just assume what we have to say isn’t approved by ANY government agency, medical organization or pharmaceutical company.
Information and Products on this website are not intended to diagnose, treat, cure or prevent any disease. If you are pregnant, nursing, taking medication, or have a medical condition, consult your physician before using our products. See Full Disclaimer on FAQ page.
AFFILIATE or WHOLESALE
If you are a health practitioner or have a marketing venue, ask us (in separate email) about how to be a SALES REPRESENTATIVE for the AquaCure.
Don’t ask such questions on your order form because the mailroom is not authorized to answer such questions.
Or, if you want to be a MANUFACTURER of Brown’s Gas machines (for your own business and sales); we are developing an online manufacturing course, that will allow any DIYer in their garage (or bigger shop) to build AquaCures.
We ALREADY have such a course. but the COVID restrictions stopped people from being able to come to our shop to learn from us directly (it was a 3 day intensive), so we are converting the course into an ONLINE version. If you are interested, please sign up to our eNewsletter to be notified when the manufacturing course is ready.
The reason for training others (and helping our ‘competition’) in any way we can… is because we are trying to get this technology into every home… And we cannot do it alone. We need LOTS more people building these machines! Not only is the NEED there (Brown’s Gas is AMAZING) but the DEMAND is also there… We are selling every machine we can build!.
You would not be building them for us, but for your own business, INDEPENDENT of us. Our plan is to have lots of small manufacturers instead of one large mega-factory. We think this consortium of small manufacturers will get machines into every home faster, while starting an entire new ‘grassroots’ industry AND provide the technical support that any ‘new’ technology needs.
We can teach you everything you need to know to successfully duplicate the AquaCure machine.
We would negotiate a royalty agreement that would start with an upfront deposit (Teaching Fee).
Notes of interest:
Eagle-Research is based in the USA, so all orders are in USD. But our USA facility is currently working on some R&D projects, and COVID border shutdowns make business more difficult, so for now all orders are currently shipped from our Canadian facility in Ontario Canada.
I’ve done everything I can to reduce the cost of the machines and still make enough money to stay in business. In fact you’ll note that the cost of the AquaCure is about half of many of the ‘other options’ out there; ‘options’ that don’t have all the safety features, the functionality or the ‘upgradability’ that the AquaCure does… Because I’m TRYING to make the most functional AquaCure affordable to as many people as possible.
NOTE: For people who find the upfront cost of our electrolyzers high for their budget, USA PayPal offers USA residents a financing option.
The financing is 6 equal monthly payments + a small finance fee.
To get the financing, just purchase the product using the PayPal option as you check out (you’ll need a registered PayPal account) and the financing option will automatically be presented to you (if you qualify) during the normal checkout (payment) process.
The ‘finance option’ is presented to you once you ‘log into’ PayPal but BEFORE you actually purchase, so you can see if you quailify before actually spending your money.
Most people who have had their ‘verified’ PayPal account for longer than 3 months will qualify for financing.
Questions about the “Bill Me Later” PayPal financing program should be directed to PayPal Customer Support at (866) 528-3733
Obviously the PayPal phone number above will give you the most updated information but here are my understandings to getting a qualifying PayPal account.
1. Apply for a PayPal account (it’s free at PayPal.com).
2. Attach at least 1 bank account and credit card (even if it’s a debit card).
3. Use the account for online purchases (like eBay) and handling money transfers (at least a few transactions, to/from bank or credit card). I really enjoy using PayPal, it’s VERY convenient and SAFE.
4. I don’t know how they’ll decide for you, but in about 3 months they gave my account the financing option.