Posted on Leave a comment

Over filled AquaCure

 
If the AquaCure has a high liquid level alarm and it’s over-full, 

the alarm will be shrieking and the gas production will shut off.

Sometimes the AquaCure Tower Cap will ‘retain’ fluid when you are filling it; due to a vapor lock preventing the water from dropping into the electrolyzer.  
I mention this effect in the Operation Manual and also that the easiest way to prevent this condition is to have the machine running as you squirt the water in (the gas production prevents the vapor lock and the water drops down into the machine).

The reason this is an issue is because if the water you are squirting in isn’t dropping into the machine, the liquid level in the sight tube won’t rise and you’ll keep putting water in… resulting in too much water.
The ‘stored’ water will drop into the machine as soon as you start up the machine, which will cause the machine to be ‘over-filled’.

Sometimes (when the liquid level is CLOSE to the full line) the problem is that when the gas production starts it actually raises the liquid level as gas takes up ‘room’ in the solution… Raising the liquid level to above the full line and the alarm goes off.  In this case the AquaCure will run for a few minutes before the alarm goes off.

To fix, you have two options:

1. If the AquaCure will operate for short times, just run the AquaCure the short times until enough water is used up (converted to gas) that the liquid level drops to where the alarm doesn’t go off anymore.  But that option would be annoying.

2.  You remove some fluid (see below).  SAVE the fluid, because it contains lye that you need to put back into the machine.

The obvious way to remove excess fluid is to dump some out… But that’s inconvenient; particularly if you’ve filled it so far that you have liquid in the Tower Cap, because removing the Tower Cap would cause the solution to pour all over the machine.  If it is that full, it’s best to drain out enough of the excess through the Tower Cap ‘gas out’ fitting, until the liquid level is low enough to take the Tower Cap off without spillage.

Note that it’s ALWAYS a good idea to wrap a cloth around the base of the Tower Cap when removing it anyway, because there will always be at least condensation drips.

If you can remove the Tower Cap without spillage, the simplest way (I’ve discovered) to remove excess fluid from the AquaCure is to cut a 6” section off one of your 1/8” ID hoses (I cut it off the humidifier to drinking bubbler hose) and attach it to your syringe.

Tube on Syringe
Tube on Syringe

Then you can SUCK the excess fluid out of the AquaCure (with the syringe) and squirt it into a jar (that you can seal for storage).  
Then, once the AquaCure liquid level has dropped sufficiently, you can squirt the fluid back in.

Obviously, you’d remove the Tower Cap to suck electrolyte as above.  

Note: normally pure water can be (and should be) squirted into the Tower Cap check valve but you’ll be SAVING  the excess fluid you drain (from over-filling) so you’ll squirt that fluid back into the AquaCure through the check valve when it needs more fluid.  

It’s NOT a good idea to remove the Tower Cap for normal water filling; The Tower Cap is not designed to be regularly taken off (only for maintenance purposes).  Also the duckbill check valve needs regular cleaning, which is accomplished every time you squirt clean pure water through it.

NOTE: Sometimes (very rarely) the upper fluid level sensor will become too sensitive due to local conditions (atmospheric pressure, temperature, humidity… it’s an electronic thing) and alarm when the fluid level isn’t actually too high.  In this case you adjust the sensitivity of the upper sensor (it’s easy, I’d send you instructions)

Posted on Leave a comment

Why / How does HydrOxy help healing?

From a Health Practitioner:

“Fascinated by your research and discoveries in regard to health as I am a health practitioner that uses many alternative methods such as PEMF, EWOT, Lasers, electric stim, vibration, etc. I know you can’t make medical claims, but how might this therapy affect cancers, infections, etc., in other words, what is the mechanism by which Brown’s Gas can possibly affect cancer or viruses or bacteria or fungi?”



WOW, you cut right to the point 🙂

Simply put, hydrogen is a FOOD and corrects a hydrogen nutrition deficiency that has resulted in illness and ailments.

Our bodies are fantastic machines and know how to heal themselves, if given what they need to heal.

But they also ‘know’ how to survive when NOT given what they need.  

An example is when the body gets cold, it knows to shut off blood flow to the extremities to preserve core temperature.

Similarly, with hydrogen deficiency, the body starts shutting off ‘extraneous’ (not immediately life threatening) systems, to preserve life.

The first thing that shuts off is the regeneration systems, so wounds scar instead of healing.

The next thing to go is the immune systems, so people get sick and eventually ‘auto-immune’ diseases happen.

The last thing is that organs start to shut down.

All this happens even when people are drinking enough water and eating plenty of food (more below)


People are (by volume)  62% hydrogen, 24% oxygen, 12% carbon and 2% everything else.

Hydrogen is our most important macro-nutrient.  Every detail of our bodies are built using it in one way or another, even our DNA is assembled around a spine of water.  Every chemical process uses hydrogen directly or indirectly.

We cannot get hydrogen by breathing air, like we get oxygen.  

Hydrogen is tightly bound on this planet because once released, it rises back to God.  

We get our hydrogen from our FOOD (hydrocarbons)

It takes a lot of energy to pull hydrogen away from the molecules it is bound to, so that it can be used.  To survive we depend on one of the earliest forms of life… Bacteria.

There are specialized bacteria in our Colin that complete the job that our digestion system prepared (with mastication, enzymes, acids, etc)

EXCEPT that the modern miracle of antibiotics, artificial sweeteners and a thousand other chemicals KILL these sensitive bacteria… 
Also, we generally are not eating the kinds of foods these bacteria like (such as fiber) so other forms of organisms (like candida) tend to push them out.

And if there are not enough of them, the food doesn’t complete it’s digestion and we become hydrogen deficient.  Most of us (on the planet today) are now hydrogen deficient.

So, with hydrogen supplementation an AMAZING thing happens…

First organs come back to life, doing what they were intended to do.  In my case, my heart healed a bad valve (heart murmur) that I’d had since childhood.  My skin lost it’s psoriasis, my hair is growing back, etc.

The next thing that happens is the body’s immune systems come back online.  
In my case I haven’t been sick (with anything) since 2005 when I started drinking HydrOxy enriched water) and (once I started breathing HydrOxy in March of 2016) my body was able to heal from hand warts and a planter’s wart (viruses) that I’d had since childhood.  

The next thing that happens is the body’s regeneration systems come back online.  In my case all my scars (again, that I had since childhood) disappeared, wounds and sprains heal extraordinarily fast and I look 15 years younger than I did 3 years ago (pictures to prove).

In addition to all that, physical ability improves (both strength and endurance), noted by many athletes.

Many people are suffering needlessly and dying from a nutritional deficiency no one even knew they had.
By supplementing with hydrogen, they regain their health (their body’s heal themselves) and enjoy quality of life.

HydrOxy is a therapeutic mixture of hydrogen, oxygen and ExW.

ExW is a major component of HydrOxy (Brown’s Gas).  

What is Brown’s Gas?
https://eagle-research.com/q-what-is-browns-gas-bg/

Soooo…..What is ExW and why does it matter?
https://eagle-research.com/what-is-exw-and-why-does-it-matter/

So, to answer your question now that you have some context…

HydrOxy doesn’t do anything to cancer or viruses or bacteria or fungi.  

The AquaCure provides the gaseous mixture (HydrOxy) that is the FOOD (nutrition and energy) the body needs to heal itself and then rejuvenate to a healthful vitality.

With the body’s organs and immune systems functioning correctly, virtually all cancer, pathogens, fungi, etc. are eliminated and with the regeneration systems back online, wounds and organs heal quickly.

Any good Doctor knows that they do not heal.  The BEST they can do is mitigate catastrophe and give the body what it needs to heal itself.

Posted on Leave a comment

What is Brown’s Gas vs OxyHydrogen?

Just mixing pure hydrogen (H2) and oxygen (O2) in a ratio of 67%:33% does not make the gas ‘Brown’s Gas’.  

Just as if mixing hydrogen and oxygen from bottles in a 67:33 ratio does not make Brown’s Gas.  Brown’s Gas has 6 different constituents / combinations of H and O.  A mixture of pure molecular H2 and O2 has only those 2 constituents, thus is called OxyHydrogen, not Brown’s Gas.

Brown’s Gas (aka HydrOxy or HHO) contains:
Diatomic hydrogen (H2)
Diatomic oxygen (O2)
Negatively charged Plasma form of water (ExW)
Water vapour (H2O)
Monatomic hydrogen (H)
Monatomic oxygen (O)

The HydrOxy name was coined back in the 1980’s by a New Zealand man names Alvin Crosby, who was a distributor of Yull Brown’s and started making his own version of Brown’s Gas machines and (because Yull Brown was upset with him) Alvin made up a new trade name for the gas… HydrOxy.

Similarly, the name HHO was another trade name for Brown’s Gas, made up by Denny Klein of Florida in the USA, in the 1990’s when he was attempting to attract investors by ‘patenting’ this ’new’ gas.  Of course his patents were worthless because just changing the name doesn’t change the actual gas characteristics or the technology to generate it.

Thus HydrOxy and HHO are two (of the many) names for Brown’s Gas.  So what is Brown’s Gas? 

Note the video in my 2019 Germany presentation shows the ExW (the third most prevalent constituent in Brown’s Gas) being generated.

The “electron rich plasma water vapor” which I call ‘electrically expended water (ExW) is ONLY created in specially designed electrolyzes that do NOT have a membrane between the anode and cathode.  I discovered this plasma form of water in 1996.

PEM/SPE electrolyzers have a ‘membrane’ (the solid polymer electrolyte) so cannot form the conditions required to make ExW, thus cannot ever make Brown’s Gas (HydrOxy or HHO).  It’s physically impossible.


This ’plasma’ form of water (ExW) can ONLY (as far as I know so far) be formed in the area between electrodes that do NOT have a membrane that ’separates’ the hydrogen and oxygen from each other during the electrolysis process.  

Cations and anions need to make a kind of ‘semiconductor bridge’ in the solution between the electrodes that can then stuff electrons into water, making an electron rich gaseous form of water that is NOT part of the Faraday Equations… 

Which is why properly designed Brown’s Gas electrolyzers seem to be ‘over-unity’; producing more gas than Faraday equations predict.  Because the ExW is a ’side effect’ of the electrolysis process and not part of the Faraday Equations.

View a quick efficiency test of the AquaCure AC50; indicating about 98% efficiency


Electrolyzers using PEM/SPE effectively have a ‘membrane’ and can NEVER make ExW.  It’s physically impossible.

Further ‘combining the ports’ will NOT make Brown’s Gas (or HydrOxy or HHO), that’s a miss-understanding you need to correct now, or I’ll be forced to ‘expose’ it.  

It’s bad enough that no one can settle on a single name for Brown’s Gas, we cannot allow gas mixtures that are not even Brown’s Gas to carry any of its names.

Combining the ports of 99.9% pure H2 and 99.9% pure O2 is about the same as just using bottled hydrogen and oxygen, which will NEVER make ExW which is a defining characteristic of Brown’s Gas (HydrOxy or HHO).

What you are producing (when you combine pure hydrogen and oxygen) is often called OxyHydrogen… 

OxyHydrogen is often confused with Brown’s Gas by people who do not know the difference… Like these unfortunately miss-informed folks at WikiPeadia.

https://en.wikipedia.org/wiki/Oxyhydrogen

Posted on Leave a comment

What to look for when considering The purchase of any hydrogen technology

1. Safety:

Like anything, HydrOxy (aka Brown’s Gas, BG or HHO) is safe if handled correctly.  Look for a machine that has safety features like:

a. Low liquid level shutoff (because electrolyzers that run out of fluid can explode)

b. High Pressure electrical shutoff (to stop making gas if the pressure rises, because if the pressure rises too high the electrolyzer can explode).

c. Low operating pressure (because the higher the pressure, the more violent the explosion).  The AquaCure has an operating pressure of  ~2 psi, many others operate at 20 psi (the potential explosive difference is like a balloon or a bomb).

d. Mechanical High Pressure Relief Valve (because electronic switches can fail, so a backup is needed)

e. Timer switch (so machine automatically shuts off)

f. Adequate scrubbing and/or means to keep the gas clean and pure.

g. A machine that is safety certified and exceeds all international safety standards.

2. Proven Customer Satisfaction

a. A business that has been building and selling electrolyzers worldwide since 1986 with 98% customer satisfaction.

b. A business that will tell you ALL the dangers and teach you how to operate the machine safely.

c. A business that will work one-on-one with customers to answer any questions.

3. Low and/or easy maintenance 

4. Lifetime Warranty

5. 1 year satisfaction guarantee or full purchase price refunded.

Posted on Leave a comment

Is hydrogen inhalation better than drinking HRW?

I saw a study like this years ago, where they examined 321 studies to reach several conclusions.

One of which drinking HRW was (for some ailments) more effective than ‘continuous’ inhalation. 

And the HRW proponents took that statement out of context to ‘prove’ that people didn’t need to inhale… So they could stay in business.

But the study also said that for some ailments intermittent inhalation was more effective than HRW.

Therefore, the MOST EFFECTIVE therapy, to include all ailments is to drink HRW and to intermittently inhale hydrogen.

And in our case, we also add ExW and frequencies, so we are already in the ‘next generation’ of therapy.

The interesting part for us, is that the body needs to intermittently get hydrogen, so obviously it needs a ‘rest and absorption’ period after hydrogen is applied (even with HRW) to be most effective.

This correlates well with EATING, where when we get hydrogen from our food, it is intermittent.

And I noted years ago (and say so in my protocols) that many shorter sessions is more therapeutically effective than one long session.

https://drinkhrw.com/blogs/news/why-h2-concentration-matters

The HRW people have to say SOMETHING to stay relevant.  Including ’skewing’ the science.

The studies clearly show that for some aspects of some ailments, drinking HRW is more beneficial than inhaling but they ‘cherry pick’ this out of the main body of data that shows the inhalation is 10x more effective for many more aspects of most ailments.

In other words, you need BOTH.  You need to drink HRW and inhale… And BTW, pure H2 is obsolete.  

HydrOxy is more therapeutic (gets better results)…

But the hydrogen ‘industry’ obviously can’t say that or they’d be cutting their own throats.

And as a fact… Inhaling HydrOxy (Brown’s Gas) for 12 seconds puts as much hydrogen into your blood as drinking a full liter of 1.6 PPM of HRW (there’s only so much hydrogen that you can ’stuff’ into water… So the ‘concentration’ of hydrogen in the water becomes largely redundant when also inhaling.

Posted on Leave a comment

Is MORE hydrogen (HydrOxy) better?

It’s important to note that MORE is NOT better and that QUALITY is more important than QUANTITY.

First, therapeutic effects can be had with 2% hydrogen in the intake breath.(most scientific studies use 2%) 

Second, once the blood is saturated with hydrogen, you breathe OUT as much as you breath in, so any ‘extra’ is irrelevant and wasted.

Third, worse than wasted, because mixtures greater than 4% hydrogen in the intake breath are potentially EXPLOSIVE.  

Why is it that I seem to be the only one pointing this out?

So the ‘intake breath’ mixture containing hydrogen should never exceed 4% hydrogen by volume.

Therefore MORE is NOT better.  

What needs to happen, for maximum therapeutic benefit (when breathing), is the gas volume adjusted so that you are getting at least 2% hydrogen and maximum 4%.

AND, since it takes about 15 minutes for a body to fully saturate with hydrogen, and about 15 minutes for levels to drop once breathing hydrogen stops, it’s our opinion that multiple breathing times during the day is more efficient and therapeutic than a single long session.

That said, when bubbling water for drinking or bath, more is better, because you want to infuse the water with HydrOxy as quickly as possible and maintain high levels in the water as your skin soaks it up.

The next thing to consider is QUALITY of the gas.

Hydrogen alone is good, but when you add ExW (using HydrOxy), it further improves therapeutic benefit because it adds bio-available ENERGY to the body.

Bodies that are chronically dehydrated and sick (or wounded) have compromised energy generation systems and depleted energy stores.

ExW is a negative (electron-rich) plasma form of water that DIRECTLY gives the body energy to heal.

All that said, the AquaCure is capable of 75 LPH (or 1250 mLPM).  

I currently control the gas output (throttle it down) to a safe breathing level by using a very lean electrolyte solution.

If people want more volume of HydrOxy, (like for bathing application) they can add more lye.  

But if they do increase the gas output, they need to use a valve (included with every AquaCure) to restrict the gas flow back to safe breathing levels.

My new AquaCure (which I’ll be selling soon) has a user-friendly 0-100% gas adjustment on the front, so gas volume can be adjusted for an infant, to an adult, to full production volume level to quickly infuse a bath.

_________________________

Now, as per the question about volume of gas to breathe.

The way the statement and questions are worded is very confusing to me because the ‘measurements’ and references are incomplete and taken out of context. 

The bottom line is that any air that has greater concentration than 4% hydrogen is potentially EXPLOSIVE and this is not made clear by manufacturer’s like Vital Reaction.

Our original AquaCure did the same thing that MOST manufacturer’s do, simply limit the MAXIMUM gas production to something reasonably safe for an adult to breathe. 

In our case, we did it by putting only 1 ounce of lye into the machine, so it couldn’t produce more than about 18 liters per hour (L/h) of HydrOxy gas (12 L/h of hydrogen and 6 L/h of oxygen).

So we COULD (for the most part) just have people breathe 100% of the gas volume coming out of the original AquaCure… because it was limited to 12 L/h of hydrogen.

BUT, like many others, this was TOO MUCH hydrogen, if a small person was breathing it.

So, unlike ‘everyone else’, the AquaCure actually had a way to SAFELY cut down (reduce) the gas volume… 

Using the ‘restriction valve’ on the torch handle.

If you try this with most of the ‘other’ manufacturer’s machines, the internal pressure will rise dramatically and either vent off excess gas or explode.

But this method of restricting the gas output, while possible, was inconvenient, because unless tedious gas volume measurements were done, the gas volume was just being ‘guessed at’ by watching the bubble flow.

We are all about safety, user-friendliness and convenience.

So with the AquaCure Model 50 we’ve done something few have yet done.  We added electronic gas volume adjustment.  

So it becomes REALLY EASY to accurately adjust the gas output for safe breathing… For any sized person.

ONLY breathing requires this gas volume reduction.  For all other applications / protocols, it’s more advantageous to have higher gas production.

So the AquaCure Model 50 now has a full 100+ grams of lye (4 ounces) and it’s 100% gas production is increased to 50 L/h.  

This gives more than adequate gas production for all protocols and the gas volume can be accurately reduced (for breathing) at the touch of a button.

Note that we typically report our gas production with electrolyzer ‘industry standard’ of Liters per hour, established decades ago.  

However, because the uneducated and noncompliant manufacturer’s now often use measurements like milliliters per minute (mL/m), I provide those measurements too, so people can try to compare apples to apples.

Note that HydrOxy is only 2/3 hydrogen, so you also need to factor that in when comparing HydrOxy gas production to a ‘pure’ hydrogen generating machine, like the Vital Reaction.

And the Vital Reaction (like ALL pure hydrogen technologies) does NOT and cannot generate ExW.

Most don’t even know what ExW is…

Or how ExW is ‘vital’ to helping the body heal and maintain health. 

To directly answer the question.

The gas production of the AquaCure has only 66% hydrogen, so is NOT directly comparable to the Vital Reaction gas production, which is 100% hydrogen.

The AquaCure is DESIGNED to keep you SAFE with near the MAXIMUM (4%) of hydrogen in the intake breath.

So, NO, we do NOT recommend increasing the AquaCure gas production for breathing, beyond the math given in the Operation Manual.  (max 40% duty cycle for a full grown and large adult) which would be about 20 L/h of gas, (which is about 13 L/h of hydrogen and 7 L/h of oxygen).

So any manufacturer who is having you breath more than 13 L/h of hydrogen is having you breath a potentially explosive mixture. 

That said… Many people DO breath more than 13 L/h of hydrogen and that’s OK as far as ‘toxicity’ goes, because the gas is not toxic.

But they need to have ‘informed consent’.  A full understanding of the risk that they are taking… Because the gas is potentially explosive.

Particularly because (with very few exceptions) there is NO GOOD REASON to breath more than a 4% mixture of hydrogen.

When the blood becomes saturated with hydrogen (takes about 10 – 15 minutes), you breathe OUT almost as much hydrogen as you breathe IN.

And MOST of the (1,000+) scientific studies are showing therapeutic benefits at 2% hydrogen in the intake breath…

So 4% is already double that.

Posted on Leave a comment

More HydrOxy Gas is NOT ‘safer’

__________________________SMALL is GOOD (a writeup I’m working on)_________________________________

Note that therapeutic volumes of hydrogen are SMALL!  

Most of the 1000+ scientific studies test at 2% hydrogen in the intake breath (about 9 L/H for an adult or 20% setting on the AquaCure).  

We know people BELIEVE what the SEE and THINK ‘more is better’.  So we suggest about 18 L/H or 40% setting on the AquaCure, for a 4% hydrogen in the intake breath (assuming an adult breathing).

Any mixture greater than 4% of hydrogen in air is a potentially explosive mixture.  That is the danger here.

HydrOxy gas is NOT poisonous or toxic in any way.  There is NO way to ‘over-dose’.  You could literally breath 100% HydrOxy gas (no air) if you had a machine big enough to provide that volume of HydrOxy.

Note: The AquaCure can only make 50 L/H, so can only provide a supplement of 4% hydrogen into the 96% air you breathe.  

The 100% PWM setting on the AquaCure is only talking about 100% of 50 L/H, not 100% of all the air (assuming 450 L/H) you breath in.

I take precautions against static sparks (high humidity in the room, no synthetic clothing, no carpeting, etc.) I ground everything and I use nose cannulas ONLY (virtually no spark can get up into my nostrils).  It may also help to use a grounded anti-static wristband like they use when handling static sensitive electronics.

The next point is that once the blood is saturated with hydrogen, you actually breath OUT as much as you breath IN.  Which is one of the reasons there is no toxic limit.  So any volume greater than that required to saturate the blood is redundant and un-needed.  2% hydrogen in the intake breath is proven SCIENTIFICALLY to be PLENTY to saturate the blood in about 15 minutes.

My point is that MORE is NOT needed and is thus NOT better.  

MORE is possible and not dangerous in any other way EXCEPT this annoying explosive thing.  

And since more than 2% is NOT needed to saturate the blood with hydrogen, our PWM setting of 40% (which is just below the 4% explosive limit for an adult) is the most volume I’m comfortable with seeing people use.

So do not think (I know it is hard to believe) that MORE is better or even needed.  It’s not.  

I want you to be healthy and I want you to be SAFE!

It does our business good to have lots of healthy people.

It won’t do this technology any good if someone has an explosion in their lungs.

The government would likely impose sanctions on this otherwise benign and NEEDED technology like they shut down the space program the the Challenger blew up.

All that said, the less than 100% is ONLY for breathing.  For ALL OTHER APPLICATIONS / PROTOCOLS I’d personally use PWM 100% with no concern whatsoever.

Use PWM 100% to bubble water (if you are not also breathing) like in a bathtub or foot bath or just bubbling a big batch of water.

Use PWM 100% for external application of HydrOxy gas with spot applicator or bagging.  If there is a ambient pressure external explosion of the gas, it sounds sharp and loud but is no more dangerous than a balloon popping.  

It’s the internal explosions that would be dangerous to health.  Breathe less than 4% hydrogen in the intake breath and the HydrOxy;air mixture is NOT explosive.

Posted on Leave a comment

Are there links that I can research HydrOxy for health?

George Wiseman’s story:
“My WaterTorch (
watertorch.com) customers were telling me about the health benefits (like curing their cancer) since 1996. 

 But I’m pretty thick headed so didn’t start drinking BG bubbled water until 2005, (after which I’ve never gotten sick).  

So, in 2007, I optimized my watertorch technology to address the health aspect of BG (HydrOxy or HHO).  
I developed the ER50 for Health application and started selling a DIY Kit.
https://eagle-research.com/product/er50-flat-plate-kit-mini-bg-electrolyzer/

In 2010 I made some Q&D videos to introduce the health aspects of BG enhanced water (see links below)

In 2015 I started  offering to pre-assemble the ER50 Chambers.
About 2016 I started selling a fully assembled version of the ER50:
https://eagle-research.com/product/er50-fully-assembled/

All this time I was only drinking the BG bubbled water… I started BREATHING the BG in March of 2016 
https://youtu.be/QgQex8IXyHY
(after which amazing things started happening to my body).  See “Plants Don’t Lie” blog link below.

In late 2016 I gave the technology a MAJOR upgrade and re-named it AquaCure
https://eagle-research.com/product/aquacure-model-ea-h160/

In the last decade, many people have learned about the health aspects of hydrogen and they are ALL TRUE… but there’s an additional aspect that most do not yet know.

It’s called Brown’s Gas (been around since 1960) Patented by William Rhodes of Pheonix Arizona.  Mr. Rhodes called it ‘single-ducted gas’. 
FAQ: What is Brown’s Gas?
https://eagle-research.com/q-what-is-browns-gas-bg/

Electrically Expanded Water (ExW) is the third constituent of Brown’s Gas.
(Hydrogen, Oxygen and ExW).
https://www.youtube.com/watch?v=amruwdyj3j0

ExW is a negatively charged plasma form of water (electrically charged gas), containing a bio-available form of energy (electrons) that helps ALL water based life forms.
https://eagle-research.com/plants-dont-lie/

BG (HydrOxy) has ALL the benefits of ‘straight’ hydrogen supplementation, PLUS it has bio-available energy from the ExW that gives the mixture a ’turbo-charge’ for health and healing.

My most recent AquaCure brochure:
https://eagle-research.com/wp-content/uploads/2019/05/AC-Brochure-small-v4gw.pdf

This is a page I put together and have been updating since 2007
https://eagle-research.com/browns-gas-for-health/

My eNews covers a lot of information and links.  You’d read starting from about issue 55 (sorry, not up on the new website yet)

My protocols:
https://eagle-research.com/how-i-use-browns-gas-for-health-enhancement/

Here is an article I’ve co-authored with Walter Last
http://www.aquacure4u.com/portals/15/Documents/Nexus2502EnergisedWater.pdf

I’ve spoken on BG for Health at the Tesla Tech Conference in 2017 
https://www.youtube.com/watch?v=r2_nfjiewMY
and again in 2018 
https://youtu.be/RTLWJx4bl0M
and again in 2019
https://youtu.be/eeBnd0Al5fU

I also have answers to many FAQ like:

Why does BG supplementation help health?
https://eagle-research.com/why-does-browns-gas-supplementation-help-health/

What’s the best way to get supplemental (therapeutic) hydrogen into my body?
https://eagle-research.com/whats-the-best-way-to-get-hydrogen-into-my-body/

I prefer a solution that can do all four of my protocols PLUS make ‘new water’.
New Water is an entire other conversation.

Here’s my newest AquaCure
Purchase your AquaCure here:
https://eagle-research.com/product/ac50/

AquaCure AC50 Setup and Operation Video
https://www.youtube.com/watch?v=723gzax3z7Y

AquaCure Operation Manual
https://eagle-research.com/wp-content/uploads/2019/08/AC50-Operation-Manual190414.pdf

I have much more but this is a good start.

Posted on Leave a comment

Is this pure hydrogen generator better?

No, that one (and any others that use PEM technology) cannot make Brown’s Gas.  You just get pure H2.  

Some examples:

https://h2epod.com/our-products/ 

https://h2waterforlife.com/product/h2-inhaler-plus/ 

https://www.zenearth.com/product/hydrogen-inhalation/ 

https://www.h2inhalation.com/sales-and-serviceshydrogengenerator 

https://hydrogen4health.ca/product/h2pro300-99-99-pure-hydrogen-breathing-machine-w-bg/ 

https://hydrogen4health.ca/product/falcon-hydrogen-breathing-machinehnology-copy/ 

https://labriller-suiso.jp/eng/HG-004/labriller-elan.html

https://www.alibaba.com/product-detail/Home-Use-H2-Life-Hydrogen-Inhalation_60746879889.html

https://www.vital-reaction.com/collections/hydrogen-inhalers 

https://www.alibaba.com/product-detail/Hydrogen-Therapy_62016246073.html 

Nothing wrong with pure H2, it’s just technology that is obsolete compared to the therapeutic value of BG, because pure H2 does not have ExW.

The added electrons from the ExW give the body the ENERGY needed to mitigate oxidative cascade and jump-start the entire healing process.

Hydrogen is a nutrient, a building brick.  Nothing happens to it without ENERGY.

Old and sick people have compromised energy generation systems and have depleted their energy reserves… So while pure hydrogen is GOOD and helpful because you give the body the nutrient it’s NOT getting enough of because of compromised digestive systems… Pure hydrogen alone cannot ‘do’ anything without energy (electrons).  So the BG gives BOTH the hydrogen AND the electrons to maximize therapeutic value.

PEM/SPE technology *CAN* provide both gasses – Hydrogen and Oxygen (re-combined in the output tubing) – however, they are created on separate sides of the membrane, and the ExW and free electrons are created in between the electrodes in a Brown’s Gas/HHO device.  

The electrodes in a PEM/SPE device are physically separated by the membrane and therefor (quite literally) cannot make the ExW, the membrane prevents it.

While ALL studies that use pure hydrogen are applicable to Brown’s Gas as well, we have seen conditions that respond to Brown’s Gas that are documented to not respond to Hydrogen in the “studies” done with Hydrogen only.

We can call it “static hydrogen” compared to the “energy filled gas” that is created in the BG electrolyzers.  

With BG, you also get both diatomic (H2) and monatomic (H) forms of Hydrogen with a BG machine (in addition to O2 and “singlet” O).  
https://eagle-research.com/q-what-is-browns-gas-bg/ 

If you simply want static Hydrogen, you can order cylinders of Hydrogen and get the same effects as a PEM/SPE device.   :o)

Posted on Leave a comment

What plate material do you use in the AquaCure?

This question is often asked by people who do not understand the different types of electrolyzers or the concept of ‘electro-deposition voltage’.

Electro-deposition voltage is the cell voltage limit (for any particular material) where the negative electrode (the cathode) will start to decompose and move to the positive electrode (the anode).  

If an electrolyzer is designed to keep the cell voltage UNDER (less than) the electro-deposition voltage, the electrodes will NEVER decompose.  This is why we can have a lifetime manufacturer’s warranty on the AquaCure.

As for electrolyzer design, there are several things people need to know to properly compare electrolyzer technologies.

First, the difference between ‘flow-through’ and ’tank’ electrolyzers.

Flow-through electrolyzers receive tap water input, treat the water as it ‘flows through’ the inner electrolyzer and splits the output into two streams… Low and high pH.  These electrolyzers do not use an electrolyte to lower the cell voltage so MUST use exotic electrode materials (with high electro-deposition voltages) to mitigate the electrode decomposition.  The Also, this type of electrolyzer puts ALL impurities into the output water streams…  

Further, it turns out that the high pH (alkaline) water being healthy is a myth built on 40 years of miss-understanding and propaganda.  The water WAS HEALTHIER, but not for the reason of pH.  It turns out that the reason the water was healthy was because of the added hydrogen from the cathode.

Experimenters took away the pH, (made the water neutral), but maintained the hydrogen and the health benefits were maintained.

Then they took away the hydrogen and maintained the pH and the health benefits disappeared.  Read more about that here:

Tank electrolyzers generate the hydrogen (and oxygen) with electrodes submerged in a tank of solution.  Generally there are two main types of tank electrolyzers. 

PEM/SPE electrolyzers use a ’solid’ material as the catalyst

https://en.wikipedia.org/wiki/Polymer_electrolyte_membrane_electrolysis

PEM has many advantages but has two severe disadvantages.  

First, it tends to have a high cell voltage so (again) requires exotic electrode material and

Second, it cannot make electrically expanded water EXW.

Traditional tank electrolyzers (Faraday design) have a membrane that separates the hydrogen and oxygen gasses, which then exit the electrolyzer from two separate hoses.  This is similar to the PEM design and suffers the same two severe disadvantages.

Brown’s Gas (BG, HHO, HydrOxy) electrolyzers use a more modern technology that keeps the cell voltage low using a catalyst solution and NO internal membrane.  This means they can use stainless steel electrodes instead of exotic and expensive materials like titanium or platinum and the stainless steel plates will not decompose.

Further, in addition to hydrogen, Brown’s Gas electrolyzers create a ’negatively charged plasma form of water (ExW) that give the body ENERGY (bio-available electrons) it needs to HEAL itself… Making Brown’s Gas the gas of choice for therapeutic use.

Finally, BG electrolyzers do NOT allow any impurities to leave the electrolyzer, so the catalyst and anything else stays in the tank (to eventually be rinsed out) leaving only PURE gas output to be used.

After the initial solution of catalyst (usually lye mixed with water) is put into the machine, you ONLY add pure water to top it up because the catalyst stays in the machine.  ONLY the water gets ‘consumed’ by the process.

See this link for more information on various ways to get hydrogen into your body:

More helpful links:
See Brown’s Gas testimonials / studies / etc. here:
http://eagle-research.life

Purchase your AquaCure model AC50 here:
https://eagle-research.com/product/ac50/

AquaCure AC50 Setup and Operation Video
https://www.youtube.com/watch?v=723gzax3z7Y

AquaCure AC50 Operation Manual
https://eagle-research.com/wp-content/uploads/2019/08/AC50-Operation-Manual190414.pdf

AquaCure Brochure
https://eagle-research.com/wp-content/uploads/2020/02/AC-Brochure-small-v4generic.pdf

Setup your AquaCureAC50 torch attachment:
https://www.youtube.com/watch?v=v2ufQWJ0l0Q

H2 Hubb AquaCure AC50,  Unboxing, Setup and Test videos:
Unboxing   https://www.youtube.com/watch?v=i5CAuVYu_a4&t=368s
Setup    https://www.youtube.com/watch?v=PAmDyKdai4Y
Test gas production   https://www.youtube.com/watch?v=w1GOztHEOgk