Posted on Leave a comment

What is pH? FAQ

What is pH?

 I have been trying to understand pH for over 20 years now. It has turned out to be a far more complicated subject than I first thought.

It is… Mostly because there are several interrelated factors that change pH, some healthy, some not.  So it’s important to choose the healthy options 🙂

Here is a link to help understand pH in relationship to hydrogen:

Higher pH is better, but ONLY if it’s because of the healthy options.  

And the pH rise is ‘incidental’ when molecular hydrogen is added, because H2 is pH neutral.  There are no extra electrons.

It’s the ‘other’ factors (that are also healthy) that raise the pH.  Some types of electrolysis add electrons (in addition to the hydrogen) which then raises the pH naturally and healthfully.  NOT like adding a metal like sodium to raise the pH.

I will be greatful If you can add to my understanding. I think we can agree the pH of all the organs and tissues of the body is an important factor in health.  So important that each breath factors into the pH of the blood as the blood has to be maintained within a very tight alkaline parameter.  I have learned that the stomach, skin and colon are better if they are acidic and the Gall Bladder and Small intestine need to be alkaline.  Each cell has an alkaline pH of 7.25-7.35 within the cell and an even higher pH in fluids outside the cell. 

All the above is correct in my understanding and opinion.

I also have learned that pH is another way of saying it is a measurement of electrons in a solution.  

So a pH of 7.35 is the same as -25 millivolts. A pH over 7 is measured in negative millivolts 

Because of ‘extra’ electrons.

What you are describing can be measured with an ORP meter.

and a pH under 7 is measured in positive millivolts. And as I know you know pH stands for potential hydrogen.  I believe you have said that if you put Browns Gas into distilled water which of course has neither positive or negative millivolts 

Actually, most distilled water is positive ORP (electron deficient).  

but is neutral 

Just because water is pure does not mean that it’s neutral.

that the pH will increase. 

Correct.  NOT because of the added H2, but because of the ExW component in the Brown’s Gas.

ExW is a negatively charged (excess electrons) plasma form of water.

If I am understanding you correctly this clearly shows that with the addition of hydrogen in the water not only does the water have more elemental hydrogen but because of that increase the pH as expected also went up.

Not because of the H2.

 When a hydrolysis 

Hydrolysis is the wrong word.  Look up the definition.  It’s a completely different process and people miss-use the word all the time.  A pet peeve of mine.  The correct word is electrolysis.

unit adds more hydrogen to the water it also increasing the pH.

Not because of the H2, but because of the ExW (or other way that adds electrons).

 I do not think is correct to say those units are only helpful because they increase hydrogen and the pH increase is not a factor because from my understanding they are linked.

They are somewhat linked but it isn’t the pH that is ‘healthful’.  

A study was done with so called ‘alkaline’ water from an ionizer (like the kangen machines).

They removed the pH (made it neutral) and the healthy benefits remained.

They removed the hydrogen, maintaining the pH and the health benefits disappeared.

The pH was NOT the ‘healthful’ ingredient.

 Now I know the addition of any metal will alter the pH.  The addition of say calcium will make the pH higher.   This is what I see in a lot of pH waters that are on the market.  Calcium is added to the water to increase its pH and that very well may give a person no benefit and in fact may harm them.

Correct.

 To sum up my understanding I am saying an increase in hydrogen in a solution is also an increase in pH of that solution.

H2 alone will not increase pH.  Only incidental extra electrons or the addition of a mineral or the ‘concentration’ of minerals (like the Kangen does) will increase pH.

So there is a general miss-understanding of what pH really is, why pH increases, what the most healthful pH is and the way to increase healthful pH.

How to measure pH?

https://www.chem.purdue.edu/gchelp/howtosolveit/Equilibrium/Calculating_pHandpOH.htm

Posted on Leave a comment

AquaCure Frequency FAQ

How is the ‘frequency’ produced?

The ‘frequency’ is produced by the Pulse Width Modulator (PWM) on the front of the machine.


The pulses are DC (direct current) electrical signals to the electrolyzer, not Hz (alternating) ‘frequency’.   

The frequency of the pulses is what you are setting.
432 means 432 pulses (or ’timeframes’) to the electrolyzer, per second.

Then, of each pulse (timeframe), you are setting the Duty Cycle (0-100%)  

Duty Cycle is how much time (of the pulse) the signal is turned on.  
So 40% means, each pulse is turned on 40% of the time and off 60% of the time.

How to set the frequency

Description:
XY-PWM signal generator is a device that provides electrical signals at a variety of frequencies, square wave, and output levels.It is used as a signal source or excitation source for testing.Widely used in production practice and technology.

Features:
1>. With outer casing;
2>. LCD high definition display;
3>. Support UART;
4>. Support frequency adjustment;
5>. Support duty cycle adjustment;
6>. High precision detection;
7>. Support power-down memory function;
8>. 1-Channel PWM output.

Parameters:
1>. Product name: PWM Signal Generator;
2>. Model: XY-PWM;
3>. Work voltage:DC 3.3V-30V;
4>. Frequency range:1Hz~150KHz;
5>. Frequency accuracy:2%;
6>. Duty cycle range:0.00%-100%;
7>. Output Current:About 5-30mA;
8>. Output amplitude:Same to input voltage;
9>. Size:79*43*27mm;
10>. Operating temperature:-20℃~70℃;

Frequency Set Range:
Enter the settings interface when short press any button ‘FREQ+’ or ‘FREQ-’ in the normal running status to select frequency range.Automatically switch frequency range.
Pay attention to the position where the decimal point moves when the button is pressed.
Display ‘XXX’.No decimal point,The minimum frequency is 1Hz.The frequency range is 1Hz ~ 999Hz.
Display ‘X.XX’.The decimal point is the penultimate, The minimum frequency is 0.01KHz.The frequency range is 1.00KHz ~ 9.99KHz.
Display ‘XX.X’.The decimal point is the third last,The minimum frequency is 0.1KHz.The frequency range is 10.0KHz ~ 99.9KHz.
Display ‘X.X.X’.The decimal point is fully lit,The minimum frequency is 1KHz.The frequency range is 1KHz ~ 150KHz.
For example:
Display ‘100’ means PWM output frequency is 100Hz;
Display ‘1.01’ means PWM output frequency is 1.01KHz;
Display ‘54.1’ means PWM output frequency is 54.1KHz;
Display ‘1.2.4’ means PWM output frequency is 124KHz;

Duty Cycle Set Range:
Enter the settings interface when short press any button ‘DUTY+’ or ‘DUTY-’ in the normal running status to select duty cycle.Automatically switch frequency range.
Duty cycle range is 0.00%-100%.

Using Steps:
1>. Connect to power supply;
2>. Short or long press button ‘FREQ+’ or ‘FREQ-’ to set frequency;
3>. Short or long press button ‘DUTY+’ or ‘DUTY-’ to set duty cycle;
4>. Connect to load.

UART Communication and Parameter Settings:
The system supports UART data upload and parameter setting functions (TTL level);
UART: 9600, 8, 1
1>. Set PWM frequency:
‘F101’:Set frequency is 101Hz.‘101’ can by replace by 001~999;
‘F1.05’:Set frequency is 1.05KHz.‘1.05’ can by replace by 1.00~9.99;
‘F10.5’:Set frequency is 10.5KHz.‘10.5’ can by replace by 10.0~99.9;
‘F1.0.5’:Set frequency is 105KHz.‘1.0.5’ can by replace by 1.0.0~1.5.0;
2>. Set PWM duty cycle:
‘DXXX’:Set duty cycle is XXX. ‘XXX’ can be 000-100.
E.g:‘D051’ means PWN duty cycle is be set as 51%.
3>. Read set parameter:
Send ‘read’ and then get parameter.
4>. Return value:
Return ‘DOWN’:Set success.
Return ‘FALL’:Set fail.

Note:
1>. It’s 1-channel PWM output signals.

Package:
1>.1pcs XY-PWM PWM Signal Generator;

What frequency would be best for healing?

I do not know.  That is not my expertise.  

I am an expert in electrolysis machines and I included the CAPABILITY to impress frequencies onto the water-gas (HydrOxy) coming out of the AquaCure… 

Because I know enough about frequencies to know that (if one knows what one is doing) frequencies can further enhance healing, health and rejuvenation.

So, as per the AquaCure Manual, I advise going to the actual experts to find which frequencies would work best for YOUR body and your ailment.

We set the frequency (FREQ) to 432 pps

So the power will then pulse DC electricity to the electrolyzer 432 times a second.

It is well known that imposing frequencies on water can have healthful benefits.  There are frequencies that can assist healing and health.  The AquaCure frequency can be varied depending on the ‘energy signature’ you want to impose on the gas.  This is the biggest benefit of being able to change the frequency.

We set the AquaCure at 432 pps as a generally ‘known’ healthful frequency.  There are places on the internet where you can find frequencies that help specific ailments (research Royal Rife, Hulda Clark, Solfeggio and microcurrent frequencies lists / charts).


In the meantime, I set the frequency of the AquaCure to a ‘general good health’ frequency of 432, as advised by several people who know far more about this than I do.

There are places on the internet where you can research frequencies that help, search:
Health Frequency List
Rife Frequencies
Hulda Clark frequencies 
Solfeggio frequencies

528 Hz: Activate self-healing and positive transformation
Meditative Mind creates soothing meditation music, healing music based on solfeggio frequencies, mantra chants and various other resources for meditation, relaxation, sleep and healing. Hope our work will help you in a positive way. Blessings and Peace all the way.

https://www.youtube.com/watch?v=vTPnwiCzAs8

Another very good source of ‘frequency’ and body voltage information is Dr. Jerry Tennant.  
https://www.youtube.com/watch?v=pm-Ia6vI4PA&app=desktop&fbclid=IwAR12J94GLF30WNK7e1GC5aq3MeYp1LQU8IoxJkJUvcd55Wxi2Jw2fvHLbE4